Solar water pump for housing

Solar water pumps - Solution for pumping without gridlines

Solar water pumps enable you to move water from its remote source to where you need it, without access to power lines. Solar pumping has three primary uses; domestic use for washing, cooking and drinking, livestock watering, and irrigation. The same basics are used for all three requirements, although domestic use may require additional capabilities. We’ll discuss domestic use for this page. Solar water pumps are different from regular AC powered pumps in more ways than the simple fact that they use DC power instead of AC. Most solar pumps are designed to be used in off-grid situations, and are designed to be extremely efficient. By not experiencing losses when going from DC to AC and back to DC, you can maximize your pumping while minimizing your power use. The most efficient way to use a solar pump is PV-direct, powering the pump directly off the solar panel, without using batteries. Rather than experiencing losses through storing power in batteries, the water itself is stored in a cistern or tank to be used when needed. It’s much easier to store water than power. The difference between a cistern and a tank is a cistern has a removable lid, and a tank is generally sealed.

Submersible Solar Pump vs Surface Pump

Surface solar pump
Submersible solar pump 

Solar water pumps are typically divided into two categories: submersible pump and surface pump.  A submersible pump is installed under water, usually in a well, but can also be in a pond or stream if raised off the bottom. A surface pump is installed above the water, with an intake hose feeding the pump from the water source, and the output hose feeding the tank.  Pumps are able to push water out much higher than they are able to suck water in, so the they need to be close to the water source.  Keep the head, or the height difference between the water and the pump,as low as possible.

Morning boost

Most of us need a boost to get going in the morning; a solar pump is no different. Pumps generally require a high surge in current when starting up, but not a lot of voltage.  As a result, when solar pumps are starting in the dim, morning light, it can sometimes have trouble getting started.  A Linear Current Booster (LCB) is a device that can be installed between the solar panel array and the pump to increase the current output to get the pump going in lower light. It does so by dropping the voltage output, which doesn’t affect the water flow as much as current does. This will allow pumping to begin earlier in the day, and continue later in the afternoon as the sun is heading down – giving you more water pumped overall during the day.

A float switch can be connected to control when to turn the pump on or off based on the water level. A pump up switch will turn the pump on when the tank is low, and off when it is full. It is also known as a full tank shut off switch. A pump down float will turn on the pump when the tank is full, and off when it is empty. It is also known as an empty tank shut off switch. Some LCBs have the ability to connect a float switch input to it, rather than directly to the pump.  Be sure to check the manual of the LCB, as the on/off behavior may change when using a float switch with certain LCBs. 

Under pressure

When providing water for a house, water pressure must be created to allow the water to flow inside the pipes.  A typical house has 40 PSI (pounds per square inch) of pressure, although, as low as 20 PSI may be adequate for your needs.  Water pressure can be achieved a few ways.  Gravity feed is the most basic method; where the water is stored in a tank higher than the house. Every foot of head is equal to 0.433 PSI.  If the tank is 100’ high, it will provide 43 PSI of water pressure for your house (100’ x .433 = 43.3 PSI).

Feet Head of Water to PSI
Ft. Head PSI Ft. Head PSI Ft. Head PSI
1 0.43 20 8.66 80 34.6
2 0.87 30 13 90 39
3 1.3 40 17.3 100 43.3
4 1.73 50 21.6 200 86.6
5 2.17 60 26 500 216
10 4.33 70 30.3 1000 433


Booster pump for house pressure

If a high storage tank isn’t possible, a smaller booster pump can be added to the system to pressurize the pipes.  This pump would have to be connected to the battery bank to allow pressurizing at any time of day or night. The booster pump technical specs will show the PSI capability and how many amps are needed to create the pressure.


This should provide a general overview of solar pumping.